Kalavagunta, A., Weller, R.A.
Vanderbilt University, Nashville, TN
The four-point probe is a tool for measuring the resistivity of a material by contact with its surface. The tool is widely used in the semiconductor industry and has applications both in research and manufacturing. The method though is quite sensitive to various paramaters like the substrate material, probe separation, probe depth etc. In this paper we show that COMSOL multiphysics can be used ...
Charles Stark Draper Laboratory
Micromechanical resonators are used in a wide variety of applications, including inertial sensing, chemical and biological sensing, acoustic sensing, and microwave transceivers. Despite the distinct design requirements for each of these applications, a ubiquitous resonator performance parameter emerges. This is the resonator’s Quality factor (Q), which describes the mechanical energy damping. ...
Gaillard, N., Pinzelli, L., Gros-Jean, M., Bsiesy, A.
In recent years, a large variety of high dielectric constant materials has been studied as an alternative to silicon dioxide in order to improve the electrical properties in many integrated devices. The authors pointed out MIM electrical properties modifications such as current-voltage shift and the decrease in the voltage gap between the different conduction mechanisms voltage threshold while ...
Finite-element Analysis of Properties in Real and Idealized Photonic Crystal Fibres, Application to Supercontinuum Generation
Gérôme, F., Viale, P., Tombelaine, V., Leproux, P., Auguste, J.L., Février, S., Blondy, J.M., Couderc, V.
IRCOM, CNRS UMR 6615, Limoges, France
Using a full-vector finite-element method, we calculate modal properties in index-guiding photonic crystal fibres. The influence of the deformation of the geometry in actual fibre structures is evaluated and compared to the idealized-model. These results are applied to the supercontinuum generation. Moreover, development of MATLAB softwares for FEMLAB 3.1 are presented.
Nestlé Waters Italy
Shelf life estimation is a very important issue in the beverage industry. Depending on the packaging application, estimation of the carbon dioxide loss through the plastic bottle walls has always been desirable and challenging at the same time. In this work an FEM approach is presented, which is shown to be able to replace time consuming, expensive lab tests. Gas permeability through the ...
Bentz, D.N., Zhang, J., Bloomfield, M., Lu, J-Q., Gutmann, R.J., Cale, T.S.
Rensselaer Polytechnic Institute
One of the key issues in developing higher density microelectronics devices is the impact of the stresses induced by thermal expansion mismatches of the materials used. We have examined, using FEMLAB, the stresses due to interwafer copper interconnects embedded in multilayer structures created by bonding two wafers using an organic low-k dielectric glue, benzocylcobutene (BCB). This work ...
Gamborg Andersen, G., Petrunin, V.V., Baurichter, A.
University of Southern Denmark, Physics Department, Odense, Denmark
We used FEMLAB (Finite Element Modelling LABoratory) for modelling heat propagation in 4 dimensions (time and the 3 spatial dimensions) after pulsed laser heating of non-isotropic materials during surface science experiments. As an example, the spatial and temporal evolution of a laser induced temperature jump in highly oriented pyrolytically grown graphite (HOPG) was calculated on a ns time ...
Strauss, D.J., Trenado, C.
Institute of New Materials, Saarbrücken
Mathematical modeling at the Institute of New Materials has played a crucial role in supporting the manufacturing and design of new technologies of nanomaterials, whose applications range from transportation, electronics and optics engineering to environmental sciences. In this paper, we focus our attention to two mathematical models together with their corresponding FEMLAB simulations: The ...
Confinement Loss Computations in Photonic Crystal Fibres using a Novel Perfectly Matched Layer Design
Viale, P., Février, S., Gérôme, F., Vilard, H.
IRCOM, CNRS UMR 6615, Limoges, France
To modelize infinite photonic crystal fibre (PCF) with 2D-finite-geometry mode solver, it is necessary to use a perfectly matched layer (PML). We have performed a new type of PML design to simulate propagation in PCFs. The results obtained with index-guiding PCFs are in very good agreement with previous theoretical published results. Our PML is quickly optimized. The link between MATLAB and ...
Karpov, S., Krichtafovitch, I.
Kronos Air Technologies, Redmond, Washington
Electrohydrodynamic flow is a flow of electrically neutral gas caused by corona-generated charged particles (ions) drifting through it. The operation principles of electrostatic fluid accelerators that use corona discharge phenomenon can be described as following. High voltage applied between high curvature corona electrode and low curvature collecting electrode provides condition for ionization ...