Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

Modeling of a Counter Flow Plate Fin Heat Exchanger - new

R. Jia[1], J. Hu[1], X. Xiong[2]
[1]Department of Mechanical Engineering, University of Bridgeport, Bridgeport, CT, USA
[2]Department of Electrical and Computer Engineering, University of Bridgeport, Bridgeport, CT, USA

Plate fin heat exchangers are widely used for heat recovery or cooling purposes in many industries, such as cryogenics, aerospace and automobile industries. This paper developed a numerical model to simulate the heat transfer and fluid flow in a counter flow plate fin heat exchanger and optimize its design parameters. The conjugate heat transfer in the finned plate and fluids in the channels ...

Newtonian and Non-Newtonian Blood Flow over a Backward-Facing Step: Steady-State Simulation

M.W. Siebert[1], and P.S. Fodor[1]
[1]Physics Department, Cleveland State University, Cleveland, Ohio, USA

In this work, the fluid flow over a 2D backward-facing step is analyzed in order to provide a case study for the use of different models for the blood dynamic viscosity in COMSOL Multiphysics. Three non-Newtonian models, as well as the Newtonian model are used to study the shear stresses and the reattachment length as a function of the fluid speed. The non-Newtonian models used in this study are ...

Design of Small-Scaled de Laval Nozzle for IGLIS Experiment

E. Mogilevskiy[1], R. Ferrer[1], L. Gaffney[1], C. Granados[1], M. Huyse[1], Yu. Kudryavtsev[1], S. Raeder[1], P. Van Duppen[1]
[1]KU Leuven, Instituut voor Kern- en Stralingsfysica, Leuven, Belgium

De Laval nozzles are used in supersonic aerodynamical tubes and engines. They are also employed for the production of cold gas jets to be used in chemical reactions studies. Recently, cold gas jets have been proposed of In-Gas Laser ionization Spectroscopy (IGLIS) The nozzle has a converging and a diverging part with a throat between them. High gas pressure and temperature, and low velocity ...

Modeling Integrated Thermoelectric Generator-Photovoltaic Thermal (TEG-PVT) System - new

R. Kiflemariam[1], M. Almas[1], C. Lin[1]
[1]Department of Mechanical & Materials Engineering, Florida International University, Miami, FL, USA

2D steady state heat conduction-electric current model was created in COMSOL Multiphysics® software to study the performance of thermoelectric generator-photovoltaic-thermal (TEG-PVT) system. Four different cases were studied in the paper. In case 1, PV cells without concentrator was simulated while in case 2, concentrator ratio range from 2 to 5 was utilized, In case 3, the convection heat ...

Computation of Velocity, Pressure and Temperature Distributions near a Stagnation Point in Planar Laminar Viscous Incompressible Flow

E. Kaufman[1], and E. Gutierrez-Miravete[2]

[1]Pratt and Whitney, East Hartford, CT, USA
[2]Rensselaer at Hartford, Hartford, CT, USA

As gas turbine temperatures and component life requirements continue to rise, it becomes increasingly important to have a good understanding of the operating temperatures of their components. The objective of this study was to explorate whether a Hiemenz flow approximation based on measured static pressures near an airfoil leading edge can provide a good estimate of the leading edge heat ...

Dynamics of Rotors on Hydrodynamic Bearings

R. Eling[1]
[1]Mitsubishi Turbocharger & Engine Europe, Almere, The Netherlands

This study presents a rotordynamic analysis of a rotor on hydrodynamic bearings using COMSOL Multiphysics®. In this paper, the complexity of the model is gradually increased. Starting point of the analysis is the modal analysis of the rotor in free-free conditions. A Reynolds model is set up to predict the film pressure distribution under shaft loading. Due to the cross coupling terms of the ...

An Overview of Impellers, Velocity Profile and Reactor Design - new

P. Patel[1], P. Vaidya[1], G. Singh[2]
[1]Indian Institute of Technology Bombay, Mumbai, Maharashtra, India
[2]Indian Oil Corporation Limited, Faridabad, Haryana, India

This paper presents a simulation approach to develop a model for understanding the mixing phenomenon in a stirred vessel. The mixing in the vessel is important for effective chemical reaction, heat transfer, mass transfer and phase homogeneity. In some cases, it is very difficult to obtain experimental information and it takes a long time to collect the data. Such problems can be solved using ...

Topology Optimization of Thermal Heat Sinks

J. H. K. Haertel [1], K. Engelbrecht [1], B. S. Lazarov [2], O. Sigmund [2],
[1] Technical University of Denmark, Roskilde, Denmark
[2] Technical University of Denmark, Kgs. Lynby, Denmark

1. Introduction The topology optimization method is becoming increasingly popular as a design tool for multiphysics systems [1,2]. Topology optimization of fluid-thermal systems has been presented for example in [3] for forced convective heat transfer and in [4] for natural convection problems. In this work, topology optimization including density filtering and projection is applied to ...

COMSOL Multiphysics® Simulation of 3D Single-Phase Transport in a Random Packed Bed of Spheres - new

A. Dixon[1]
[1]Department of Chemical Engineering, Worcester Polytechnic Institute, Worcester, MA, USA

Packed beds are important in the chemical industries. Computational fluid dynamics (CFD) can simulate detailed flow and scalar transport in packed beds for improved understanding and quantitative information. We present simulations of single-phase gas flow, conjugate heat transfer and isothermal dispersion of mass in a 3D model of a randomly-packed bed (tube-to-particle diameter ratio = 5.96) of ...

Evaluation of Novel Wing Design for UAV - new

P. K. Bahumanyam[1]
[1]University of Alabama in Huntsville, Huntsville, AL, USA

Viable design alternative for the existing and fast growing UAVs which are optimized for unmanned flight is of great demand. Designing of a small scale UAV alternative to the AAI Aerosonde UAV has been considered changing the wing tail configuration of the vehicle analyzing both structural and aerodynamic performance improvements using COMSOL Multiphysics® software.