J.S. Crompton, L.T. Gritter, S.Y. Yushanov, and K.C. Koppenhoefer
AltaSim Technologies LLC, Columbus, OH, USA
Analysis of burning candles is extremely complex; combustion produces a highly non-linear temperature profile through the flame in which local temperatures may exceed 1400 °C. Heat transfer includes radiation, conduction and convection components and the low melting point of the candle wax leads to a phase change that allows mass transport via capillary flow prior to combustion in the flame. ...
M. Mor, C. Seneci, V. Zacché, C. Remino, G. Petrogalli, D. Fausti
Polibrixia, Brescia, Italy
This paper presents the study and design of a new generation oven for PET blow-molding machines. The design faced several technical challenges such as: the temperature distribution in the critical areas, the sharp curvature radius, the high PET thermal inertia and the presence of boundary elements, which affected the overall performances. The work included an analysis of the preform material ...
Simulation of the Temperature Profile During Welding with COMSOL Multiphysics® Software Using Rosenthal's Approach - new
A. Lecoanet, D. G. Ivey, H. Henein
Department of Chemical & Materials Engineering, University of Alberta, Edmonton, AB, Canada
A 3D finite element analysis is carried out, using COMSOL® software, to reproduce the thermal profile obtained with Rosenthal’s equation. The implemented heat transfer equation has been modified as a means to approximate Rosenthal’s solution. An analysis of the differences between the simulation and Rosenthal’s solution, when the geometry of the domain and the source are changed, has been ...
Comparison Between Phase Field and ALE Methods to Model the Keyhole Digging During Spot Laser Welding
V. Bruyere, C. Touvrey, P. Namy
CEA-DAM, Is-sur-Tille, France
SIMTEC, Grenoble, France
Nowadays, spot laser welding is a full-fledged part of industrial manufacturing and is routinely used due to its advantages. It generates very located temperature gradients, and therefore, induces small distortions in the pieces. The COMSOL Multiphysics® software is used to model the interaction stage of an isolated impact made with a Nd:YAG pulsed laser. The free surface evolution has been ...
R. K. Krishna, R. Ramachandran, and P. Srinivasan
Birla Institute of Technology and Science
An attempt has been made to sustain the efficiency of an air pre-heater(APH) in the long run. The APH is modeled using COMSOL Multiphysics in 3D and fed with real life conditions. Upon Heat transfer analysis, the temperature profile was found out and from that, the regions undergoing maximum thermal fatigue stress was identified. The plates of the APH to the periphery are subjected to maximum ...
N. Huc 
 COMSOL France, Grenoble, France
This session is devoted to phase change modeling in heat transfer simulations. The great interest in phase change comes from the outstanding thermal performance that it enables in particular for cooling or thermal protection applications. Alternatively, phase change can induce most of the energy cost in drying or cooking applications. In all of these cases, a thermal analysis is required to ...
J. v. Schijndel , R. v. Eck , M. Klep ,
 Eindhoven University of Technology, Eindhoven, Netherlands
The paper presents a student guide on how to implement surface to surface radiation within COMSOL Multiphysics® software for case studies found within the built environment. We included four benchmarks: (1) Radiation in a triangular cavity with infinite length; (2) Radiation between two infinitely long rectangular plates; (3) Radiation in a three dimensional rectangular enclosure; (4) Radiation ...
K.-H. Leitz , P. Singer , A. Plankensteiner , B. Tabernig , H. Kestler , L. S. Sigl ,
 Plansee SE, Reutte, Austria
Selective Laser Melting (SLM) offers great potential for future manufacturing technology. In order to extend its applicability for the processing of high melting materials like molybdenum fundamental process understanding is required. This can be obtained by multiphysical simulations that allow a look into the process. In this contribution a thermo-fluiddynamical simulation model for laser beam ...
A. Roday, and P. Nicosia
Garlock Sealing Technologies
Sintering is an important step in the manufacturing of polytetrafluoroethylene (PTFE) billets. The challenge in heating large billets stems from the inherent low thermal conductivity of PTFE. Existing literature suggests determining maximum heating rate experimentally using recommended guidelines. This paper uses COMSOL to aid in optimizing the temperature profile required for a particular ...
J. Förster, and H. Vogt
Institute of Electronic Components and Circuits
A one-dimensional model of Excimer Laser-Annealing of amorphous silicon layers which are irradiated with a KrF excimer laser is described. For realisation, the application mode heat transfer in solids is used. The model predicts a melt threshold for the energy density of the laser of 88.5 mJ/cm^2. It also predicts a linear increase of the melt duration with a slope of approximately 625 (ns*cm^2) ...